Milling Department
1)Doosan DNM 400 Vertical Machining Center
30.000” X-Axis, 17.100” Y-Axis,
20.100 Z-Axis
30 tool capacity / Double Arm
20 horsepower spindle motor (8,000 rpm)
2)Doosan
DNM 400 Vertical Machining Center
30.000” X-Axis, 17.100” Y-Axis,
20.100 Z-Axis
30 tool capacity / Double Arm / Through spindle
coolant.
20 horsepower spindle motor (12,000 rpm)
3)Doosan
DNM 500 Vertical Machining Center
40.000” X-Axis, 17.100” Y-Axis,
20.100 Z-Axis
30 tool capacity / Double Arm
20 horsepower spindle motor (8,000 rpm)
4)Doosan
DMV 3016 Vertical Machining Center
32.200” X-Axis, 16.100” Y-Axis,
20.100 Z-Axis
30 tool capacity / Double Arm
15 horsepower spindle motor (12,000 rpm)
5)Doosan
DMV 3016 Vertical Machining Center
32.200” X-Axis, 16.100” Y-Axis,
20.100 Z-Axis
30 tool capacity / Double Arm
15 horsepower spindle motor (12,000 rpm)
6)Chevalier
CNC Knee Mill
30” X-Axis, 14” Y-Axis, 6”
Z-Axis
Unlimited tool capacity, manual tool changer
7 horsepower spindle motor
7)Super
Max Manual Mill
30” X-Axis, 14” Y-Axis
5 horsepower spindle motor (3,500 rpm)
Lathe Department
1)Daewoo
Puma 2000 SY CNC turning center
11.400 diameter, 20” length turning capacity
Y axis with 4.000 travel.
20 horsepower spindle motor
Full contouring main and sub spindle
24 tool capacity (all accept rotating tool
holders)
5 horse power / 5,000 rpm rotating tools
10 horsepower sub-spindle ( full contouring
)
LNS bar feeder
3-jaw chuck, and 3J collet capability both
main and sub-spindle
2)Doosan
Puma 2000 SY CNC turning center
11.400 diameter, 20” length turning capacity
Y axis with 4.000 travel.
20 horsepower spindle motor
Full contouring main and sub spindle
24 tool capacity (all accept rotating tool
holders)
7 horse power / 5,000 rpm rotating tools
10 horsepower sub-spindle ( full contouring
)
LNS bar feeder
3-jaw chuck, and 3J collet capability both
main and sub-spindle
3)Doosan
1500 SY CNC turning center
11.400 diameter, 20” length turning capacity
20 horsepower spindle motor
Full contouring main spindle
12 tool capacity (all accept rotating tool
holders)
5 horse power / 6,000 rpm rotating tools
7.5 horsepower sub-spindle (fully programmable)
LNS bar feeder
3-jaw chuck, and 3J collet capability both
main and sub-spindle
4)Daewoo
Puma 8S CNC turning center
10 ½” diameter, 20” length
turning capacity
12 tool capacity
25 horsepower spindle motor
3-jaw chuck, 2-jaw chuck, and 5c collet capability
5)Victor 1630 engine lathe (two machines of this type)
23 ½” diameter, 25” length
turning capacity
Trav-A-Dial equipped
7 horsepower spindle
3-jaw chuck, 4-jaw chuck, face plate, and
5c collet capability
Miscellaneous
Departments and Equipment
Deburring
Department
Silver Solder Department
All inspection equipment calibrated in accordance with
MIL-STD-45662
Recall and calibration tracked by computer
surveillance
QUALITY
CONTROL
1)Quality
Control Department operating in compliance with MIL-I-45208
350 square feet of environmentally controlled
floor space
All inspection equipment calibrated in accordance
with
MIL-STD-45662
Recall and calibration tracked by computer
surveillance
